的影響1噸然氣生物質鍋爐燒燃形態原因有怎樣？
What are the factors affecting the combustion of a ton of gas boilers?
第一是
1噸天燃氣加熱爐爐排占地小。該爐排厚度不是使標準用時內進去爐排的電爐燃料以達到該裝修開發參數表下流程的耗煤量，即電爐出現溫度和持續高溫焦爐煤氣量與裝修開發汽耗率追求的不遠不近過高，其結論充分條件是壓差、減壓蒸餾量偏移裝修開發值。
One is the floor area is small. The width of the grate cannot make fuel per unit time into the grate, under the design parameters required in coal consumption, namely the boiler heat and high temperature smoke gas output requirements and design the enough, the result must be pressure, evaporation deviates from the value of the design.
第二是往返式平推爐排煤層重量受到局限制。鑒于爐排稍窄，相對應減太小煤耗，是為了增長燒煤量，只能增長爐排上煤層重量。鑒于是往返式平推爐排，煤在爐排上無生態轉動趨勢英文，只靠爐排片翹起來向后促進改革使煤在爐排上燒，當然煤層過厚，爐排片對煤，越來越是高于約定重量煤層促進改革目的降低，當健身爐排抽回時，又將剛向后促進改革的煤帶進，使煤層向后健身呈現落后，以至于煤及渣混合型起鼓，并不能即使將煤渣推入渣坑，較為嚴重的時，會令燒煤及渣頂著后拱，受損了層燃工作狀態，印象普通運作。
The second is the thickness of the coal seam in the back and forth. Because the grate is relatively narrow, the coal consumption is reduced accordingly, to increase the amount of coal burning, only the coal seam thickness is added to the furnace. As reciprocating horizontal pushing grate, no natural falling trend of coal on the fire grate, powered by backward link cock only make coal burning in the grate, too thick coal seam, however, grate piece of coal, especially in excess of the prescribed role in promoting the thickness of coal seam is abate, when activities grate withdraw, just pushing coal back to back, it will make the coal seam backward movement stagnation, and slag and coal mixing drum, can't timely pushing coal slag into the pit, serious when, can make the coal and slag with arch, destroyed the layer combustion state, affect the normal operation.
三是爐排高度不足夠，就縮短了燃煤鍋爐在爐排上駐留時，獨特是在上升煤層強度時，爐行榜程、爐排帶動頻繁未變，促使煤可以是點燃，爐渣中所含廣泛可燃質，上升了機戒不是點燃熱流失。
Is a grate length is insufficient, shorten the retention time on coal burning in the grate, especially in the increase of coal seam thickness, grate stroke, grate drive frequency constant, which is not fully burning coal, slag containing large amounts of combustible qualitative, increased the mechanical incomplete combustion heat loss.
四是內外拱設計不和睦理，進行助燃達還不足適宜情形。內外拱合作有錯，燃盡區的常溫尾氣，被視情況加以引導意義不很深，拱未能絕對爐膛有較常溫度，主燃區得還不足需有的熱能量，煤燃不透;與此同時后拱遍及爐排建筑面積較高，拱型設計使常溫尾氣出入阻撓，消弱了擾動，減少尾氣工作流程，與此同時產生喉部常溫尾氣中未燃物與大氣混合法不正常，新增了化工進行助燃財產損失。
Fourth, the arch structure is irrational and the combustion is not the best. Arch mismatch, before and after the high temperature flue gas of burning area, be directed effect is not obvious, arch cannot ensure furnace with high temperature, primary zone without proper heat, coal combustion opaque; At the same time after the arch cover fire grate area is larger, the arch structure makes high temperature flue gas flow is blocked, weaken the disturbance, shorten the flue gas flow, at the same time cause the throat not combustion in high temperature flue gas and air mixture, increased chemical combustion loss.
